فیلتر ماسک بی ال اس مدل BLS 321 A2P3 R
شرکت «بی ال اس» (BLS) محصول فوق را تولید میکند. این محصول نوعی فیلتر ماسک است که با نام «321A2P3 R» عرضه میشود. شرکت بی ال اس این فیلتر را برای ماسکهای نیمصورت و تمامصورت تولیدی شرکت خود طراحی کرده است. این فیلتر باتوجه به کد رنگی سفید و قهوهای که دارد برای جلوگیری از ورود گردوغبار و گازها و بخارات طبیعی با نقطهی جوش بیشاز 65 درجهی سانتیگراد مانند حلالها مناسب است. برای استفاده از این محصول دمای محیط باید مقداری برابر منفی 10 الی مثبت 50 درجهی سانتیگراد باشد. این محصول در محیطی با رطوبت بیش از 80 درصد کارایی خود را از دست میدهد و به این نکته نیز باید توجه داشت. از این فیلتر برای گازها و بخارات بیبو و بیطعم نمیتوان استفاده کرد. زمان تعویض این فیلتر را نیز میتوان از طریق دو نشانه متوجه شد. نشانهی اول دشوار شدن فرایند دم و بازدم بوده و نشانهی دوم احساس بو و طعم گاز است.
- دارای دو عدد فیلتر مناسب برای ماسک های نیم صورت و تمام صورت
- مناسب برای گردوغبار
- مناسب برای گازها و بخارات طبیعی
- قابل استفاده در دمای منفی 10 تا مثبت 50 درجه سانتیگراد
- قابل استفاده در رطوبت کمتر از 80 درصد
- مناسب برای مکانهایی با حجم اکسیژن بالای 17 درصد
- غیر قابل استفاده برای گازهای بیبو و بیطعم مانند مونواکسید کربن
- وزن هر فیلتر 123 گرم
Protection against gases, vapours and dusts, fumes and mists 300 Series Filters
BLS 321 A2P3 R EN 14387:2004+A1:2008
Characteristics
BLS 321 A2P3 R is a gas filter and protects against gaseous contaminants and airbone dusts. 321 A2P3 R filter is equipped with a special threaded connection allowing to use it, in pair, on BLS half masks TP2000 R o TP2000 S and on full face masks BLS 5250 e BLS 5500
Application
BLS 321 A2P3 R filter protects against organic gases and vapours with a boiling point above 65°C. It can be used with substances as solvents, toxic particles and microorganisms,etc. It is classified in terms of capacity as a class 2 gas filter (medium capacity filter) for the gas part and a class 3 filter (high capacity filter) for the dust part
Protection
Exposure limit for 321 A2P3 R filter: with half mask: for gases and vapours 48 x TLV* or up to 5000 ppm; dusts, fumes and mists 48 x TLV with full face mask: for gases and vapours 1000 x TLV or up to 5000 ppm; dusts, fumes and mists 1000 x TLV * APF as defined in EN 529:2005 standard - value for Italy
Materials
:BLS 321 A2P3 R filter is made by
filter case: ABS •
filtering component for gases: activated charcoal A2 type •
Filtering component for particles: filtering pleated layer of glass fibres Height (thread excluded): 29 mm Diameter: 93 mm Weight: 96±5 g These filters can be used on full face masks and half masks
Application, Limitation, Warning
BLS filters cannot be used in the following conditions: - when the type and concentration of contaminant is unknown. -when the oxygen content is lower than 17% in volume (which is often the case in closed environments such as wells, tunnels, cisterns, etc). -when the contaminant is carbon monoxide or an odourless and tasteless gas. -when certain conditions are dangerous to the worker health and life. -The filter must not be modified or altered. - Leave the work area if the respirator becomes damaged, resulting in difficulty breathing and/or faintness. - Persons whose olfactory sense is altered shall not use filter respirators. -The use of gas or combined respiratory protective devices during works with open flames or liquid metal droplets may cause serious risk to the operator
Filter use and maintenance BLS filters must be used in pair connected to BLS half masks model TP2000 R and TP2000 S and to full face masks model BLS 5250 and BLS 5500. Carefully read the instructions for use of the filters and the one of the equipment (half mask or full face mask) is used with. Two new filters are packed in a sealed plastic bag. Choose the filter keeping attention to the colour and identification marking and check that the filter is of the correct type for the intended use. Check that the filter is not empire (the expiry date is printed on all the filters; this date shall be valid if the filter has been kept sealed at the recommended storage). Inspect both the filter and facepiece for any breaks or damage. For use, open the sealed packet, fit the two filters to the filter housing on the half mask or full face mask, screwing the filter tightly. Mind You: the P2 filters are used by being attached to gas filters positioning them over the gas filters and fixing in place by a plastic press-fit cover (the combined filters obtained with this coupling must be used always twin). In normal use conditions, the shelf life of the filter is not only due to the pollutant concentration but to many other elements difficult to be determined, such as the degree of air humidity, the air temperature, the inspired air volume, the weariness of the worker, etc. The worker shall leave immediately the work area and replace the filters when start to smell the contaminant. At the end of the work shift, the respirator shall be stored in a clean and dry place, according to the storage conditions indicated in the user information. The BLS filters does not require maintenance and does not need to be cleaned, regenerated or blown. Exhausted filters shall be replaced at the same time and dismantled according to the National regulations and considering the substances they have retained
Storage time: 5 years (factory sealed), as shown on label - pictogram of hourglass
Storage conditions: temperature range -10°C e +50°C, Relative Humidity < 80%
فروشگاه اینترنتی ابزارآلات و تجهیزات ایمنی آچارک فیلتر ماسک، فیلتر شیمیایی، فیلتر ماسک شیمیایی، فیلتر ماسک نیم صورت، فیلتر ماسک تمام صورت، قیمت فیلتر ماسک، خرید فیلتر ماسک، کارتریج ماسک بی ال اس، زمان تعویض فیلتر ماسک و کارتریج ماسک را به راحتی در اختیار کاربران قرار می دهد.